cDAQ 9171-1‑Slot, USB CompactDAQ Chassis
NI 9381-8 AI, 8 AO, 4 DIO, 0 V to 5 V, C Series Multifunction I/O Module
Software USRP Hardware Driver 3.9.2 (or later) GNU Radio W/ GPS Unlocked TCXO Reference: ±75 ppb W/ GPS Locked TCXO Reference: <1 ppb Xilinx Spartan-6 XC6SLX150 FPGA Fully coherent 2 x 2 MIMO capability Channels: 2 TX and 2 RX, half or full-duplex Frequency range: 70 MHz to 6 GHz DC input: 6 V (DC power supply included)
24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module—The NI‑9472 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 30 V, features transient overvoltage protection between the output channels and the backplane, and has an LED that indicates the status.
300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module—The NI‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three NI‑9225 channels.
16 AI (16-Bit, 250 kS/s), 4 DI, 4 DO USB Multifunction I/O Device
4‑Slot, USB CompactDAQ Chassis—The cDAQ‑9174 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9174 also has four 32‑bit general-purpose counters/timers.
5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module—The NI‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9403 for applications such as custom, high-speed counter/timers; digital communication protocols; and pulse generation. In a CompactDAQ chassis, you can use the NI‑9403 only as a static (software-timed) digital I/O module. You cannot use these modules to route timing or triggering signals
±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module
200 kS/s, ±20 mA, 8-Channel C Series Current Input Module
16 AI (16-Bit, 400 kS/s), 2 AO (250 kS/s), Up to 32 DIO USB Multifunction I/O Device—The USB‑6212 is a multifunction DAQ device. It offers analog input, digital input, digital output, and two 32‑bit counters. The device provides an onboard amplifier designed for fast settling times at high scanning rates. It also features signal streaming technology that gives you DMA-like bidirectional high-speed streaming of data across USB. The device is ideal for test, control, and design applications including portable data logging, field monitoring, embedded OEM, in-vehicle data acquisition, and academic. The USB‑6212 features a lightweight mechanical enclosure and is bus powered for easy portability. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
CALL US FOR THE PRICE NI USB 6001-8 AI (14-Bit, 20 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB 1‑Slo